How to Install a Bathtub ( Guide).
How to Install a Bathtub ( Guide).
Blog Article
Presented here down the page you can get lots of great insight related to A Step-by-Step Guide to Installing a Bathtub.
Setting up a tub isn't precisely brain surgery, however it does need strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bathtub with a new one is also a moderately difficult task. If the old bathtub is readily accessible, the project can move speedily; if you need to open up a wall surface to eliminate the old tub as well as position the new bathtub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will need an assistant to vacate the old bathtub as well as set in the new one. Make sure you have certified on your own for the task and fit trying it. Instead of hiring a contractor to take control of a halfway-completed job, it is better to consider using one prior to you begin. Chances are you might require a professional plumber to make tube connections.
This write-up will certainly assist you mount a new bathtub in your washroom if you have actually currently bought a brand-new bathtub and do not require to change the setup of your previous water pipes.
Your tools and also material checklist need to make up the following:
Getting ready for the Installation
First of all, the supporting structure supplied with the bathroom must be fitted (if required) according to the supplier's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to ensure that if the faucet includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to stop stress on the bath tub.
Fit the versatile faucet connectors to the bottom of both taps utilizing 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its final setting.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, activate the taps to drain any kind of water remaining in the system. The process of getting rid of the existing taps can be rather bothersome due to the limited access that is commonly the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the staying water that will certainly originate from the pipes. When the supply pipelines have actually been removed, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Before carrying on to fit the brand-new faucets, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Setting up the Tub
Making use of both wood boards under its feet, position the bathtub in the required position. The wooden boards are valuable in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four little points.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the tub up until the level checks out degree.
To set up taps, fit the bottom of the furthest versatile tap connector to the appropriate supply pipe by making a compression join; then do the same for the various other faucet.
Activate the water and also inspect all joints as well as new pipework for leaks and also tighten them if needed. Fill up the bathtub and additionally inspect the overflow outlet and the regular electrical outlet for leaks.
Finally, deal with the bathroom paneling as defined in the maker's user's manual. Tiling as well as sealing around the bathtub needs to wait till the tub has been used at the very least when as this will certainly resolve it into its last setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, then you will require lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin guaranteeing that the washers remain in location in between the faucet and the sink. Safeguard the tap in place with the supplier offered backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet connectors. The previous kind should be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bathroom meets the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can move enough to crack a rigid seal, causing the water to penetrate the wall in between the bath as well as the tiling, bring about complications with moisture and also possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your components and installations. They are marketed in tubes and cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to permit the movement experienced when the tub remains in usage. The sealant can split rather very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly readily available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was made aware of that report about A Step-by-Step Guide to Installing a Bathtub through an associate on another web address. Sharing is nice. You never know, you will be doing someone a favor. Thanks a bunch for your time. Visit us again soon.
View Report this page